Using ipsecuritas with sonicwall how to#

Cloud App Security Visibility and security for Cloud Apps.Email Security Protect against today’s advanced email threats.Switches High-speed network switching for business connectivity.Wireless Access Points Easy to manage, fast and secure Wi-Fi.Secure Mobile Access Remote, best-in-class, secure access.Cloud Edge Secure Access Deploy Zero-Trust Security in minutes.Capture Security appliance Advanced Threat Protection for modern threat landscape.Capture ATP Multi-engine advanced threat detection.Network Security Manager Modern Security Management for today’s security landscape.

Security Services Comprehensive security for your network security solution.

Next Generation Firewall Next-generation firewall for SMB, Enterprise, and Government.

Do not forget to refer to the link to mitigate the vulnerability. Recently a security advisory was released by Sonicwall. You could configure IPSec Site-to-Site VPN tunnel on Cisco Firewall & IPSec Site-to-Site VPN tunnel on Ubiquiti Unifi USG as well. If you have Sonicwall at the remote site then use the same steps mentioned in this article. Configure the tunnel at the remote site to get VPN working. After selecting options in the “ Advanced Settings” tab do not forget to click “ OK” to save and apply the configuration.Īfter saving the configuration, the IPSec Site-to-Site tunnel configuration is done at SonicWall’s side. You could enable or disable as per requirement. There are many options available in “ Advanced Settings“.

6.9 Life Time: Define Life Time period.

6.8 PFS: You could enable or disable Perfect Forward Secrecy as per requirement.

6.7 Authentication: Select Phase 2 authentication method from the available options.

6.6 Encryption: Select Phase 2 Encryption AES-128, AES-192 or AES-256.

6.5 Protocol: Select protocol AH or ESP.

6.4 Life Time: Define Life Time period.

6.3 Authentication: Select the authentication method SHA-1, SHA-256, SHA-384 or SHA-512.

6.2 Encryption: Select the encryption 3DES, AES-128, AES-192 or AES-256.

6.0 Exchange: Use IKEv1 or IKEv2 as per requirement.

You could use default route or IKEv2 IP Pool.ĭefine the IPSec Proposal as per requirement.

5.2 Remote Network – Create an address object or group for the remote network which is allowed over VPN.

If you want to allow everything then choose “any”.

5.1 Local Network – Create an address object or group for local network which is allowed over VPN.

Select the local and remote network host or subnet for the VPN.

4.7 Local IKE ID: Use the identifier out of available options i.e IP, Domain, Email, Firewall or Key Identifier.

4.6 Confirm Shared Secret: Confirm the secret key.

Same secret key will be use at the remote site.

4.5 Shared Secret: Generate a secret key.

4.4 Secondary Gateway: Put the secondary IP address of the remote site and if there is no secondary IP then use 0.0.0.0.

4.3 Primary Gateway: Put the IP address of the remote site.

4.2 Authentication Method: Use the authentication method.

4.1 Policy Type: Select the policy type “ Tunnel Interface” or “ Site-to-Site“.

Here we will need to fill in the general details.

Make sure the Global VPN Settings is “ Enabled” and then click “ ADD” to configure VPN settings. Both locations are shown below in the image. VPN settings are at different positions for the “ Contemporary” and “ Classic” modes of GUI. ConfigurationĪfter login, navigate to the VPN settings.

Using ipsecuritas with sonicwall how to#

In this article, we will discuss how to configure a site-to-site VPN tunnel on SonicWall Network Adaptive Appliances. SonicWall NSA supports two types of VPN tunnels. Model: NSA 6600, NSA 3600, NSA 250M, NSA 2400 etcĭescription: This article is to discuss and show a stepwise method to configure a Site-to-Site IPSec VPN tunnel on SonicWall Network Adaptive Appliances. Make: SonicWall Network Adaptive Appliances